Лексус RX 300
+ Cars Lexus RX-300
+ Controls and operation receptions
+ Options and car routine maintenance
+ The engine
+ Systems of cooling of the engine, heating, ventilation and air conditioning
+ The power supply system and release of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Automatic transmission and interaxal differential
+ Трансмиссионная a line
+ Brake system
+ Suspension bracket and steering
- Body
- The external equipment and кузовные elements
Removal and installation top распорки an impellent compartment
Removal and installation of bumpers
Removal and installation of a cowl, its lock and decorative lattice of a radiator
Removal, installation, dismantling and assemblage of a forward door and its components
Removal, installation, dismantling and assemblage of a back door and its components
Removal, dismantling, assemblage and installation of a door of a back and its components
Removal and installation of cleaners and обтекателя a windscreen
Removal and installation молдингов
Removal and spoiler installation
Removal and installation of the top hatch
+ The salon equipment
+ Onboard electric equipment
+ Basic schemes of electric connections
|
Removal, installation, dismantling and assemblage of a back door and its components
|
|
The left door is more low considered; removal and installation of the right door is made similarly. |
Components of a back door
|
|
- Remove заглушку, turn out the screw and remove an edging of the internal lever of unlocking of the lock of a back door by means of a screw-driver.
- Wring out clamps and remove the control panel стеклоподъёмником.
|
|
- Remove заглушки screws, turn out screws and remove clamps.
|
- Insert a screw-driver between a door and its furnish and wring out the furnish panel.
- Remove the panel of furnish of a door together with consolidation. Replace its clamps and remove consolidation.
- Separate two sockets, liberate electroconducting of the block of management from the holder, turn out two screws and remove the block of management of a back door.
- Separate a socket, turn out 3 bolts and remove динамик.
- Turn out the screw of fastening of the lever of unlocking of the lock, disconnect from the lever two cables and remove the lever.
- Remove two plugs and a cover of a service aperture.
- Remove consolidation.
- Lower glass so that in a service aperture bolts of its fastening were visible. Give nuts, take glass from holders and lower it in a door.
|
|
Preliminary lay in a door rags not to scratch glass. Arrange glass as it is possible more close to переду for a door. |
- Turn out two bolts and the screw of fastening of a dividing lath and shift it forward.
- Turn a lath on a quarter of a turn and take out it from a window doorway upwards.
- Remove the fixed glass, having pulled for its top corner forward and downwards. Separate from glass consolidation.
- Accurately take out upwards from a door glass.
- Separate a socket, turn out 4 bolts and remove стеклоподъёмник through a service aperture.
|
|
Necessarily separate a socket to exclude operation possibility стеклоподъёмника and trauma receptions. |
- Remove a cover of the lever of blocking of the lock, turn out 4 bolts, separate 2 sockets and remove the lock.
- Turn out 2 screws and remove a lock casing.
- Turn out two bolts and remove the external handle of a door.
- Remove basic pillows.
|
|
- Give fixture of loops and the terminator of a door and remove it, preliminary having removed the panel of facing of the central rack of a body. For this purpose remove overlays of thresholds of forward and back doors then liberate from clamps and remove the panel of facing of the central rack of a body.
|
- At installation of the door especially new, it is necessary to adjust its position, operating with a similar case of adjustment of position of a forward door. Efforts of a tightening of bolts are specified in Specifications of the Head the Body.
- Installation is made upside-down. Tighten fixture with demanded efforts, use new clamps.
|
|
|
|
