Лексус RX 300
+ Cars Lexus RX-300
+ Controls and operation receptions
+ Options and car routine maintenance
+ The engine
+ Systems of cooling of the engine, heating, ventilation and air conditioning
+ The power supply system and release of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Automatic transmission and interaxal differential
+ Трансмиссионная a line
+ Brake system
+ Suspension bracket and steering
- Body
- The external equipment and кузовные elements
Removal and installation top распорки an impellent compartment
Removal and installation of bumpers
Removal and installation of a cowl, its lock and decorative lattice of a radiator
Removal, installation, dismantling and assemblage of a forward door and its components
Removal, installation, dismantling and assemblage of a back door and its components
Removal, dismantling, assemblage and installation of a door of a back and its components
Removal and installation of cleaners and обтекателя a windscreen
Removal and installation молдингов
Removal and spoiler installation
Removal and installation of the top hatch
+ The salon equipment
+ Onboard electric equipment
+ Basic schemes of electric connections
|
Removal, dismantling, assemblage and installation of a door of a back and its components
Components of a door of a back
|
- Insert a screw-driver between a door of a back the top panel of furnish of glass and wring out the panel from clamps on its perimetre.
- Separate a socket and remove from the top panel of furnish has flown down a top level stoplight.
- Inserting a screw-driver between a door of a back and elements of furnish of a door, wring out consistently from clamps the top panel, both lateral and the bottom panel.
- Turn out a nut and remove the screen wiper lever.
- Turn out a nut and remove a washer of the e/motor of a screen wiper from door lateral aspect.
- Separate a socket, turn out three bolts and remove the screen wiper e/motor.
- Separate sockets, turn out on 4 bolts and remove the back combined lanterns with consolidations.
- Disconnect from the cylinder of the lock a socket, turn out two bolts and remove the cylinder.
- Turn out two bolts, remove the mechanism of management of the lock and disconnect from it a cable.
- Disconnect from the lock draught, give two nuts and remove the lock activator. Separate a socket.
- Separate a socket, turn out 4 bolts and remove the lock.
- Turn out two screws and remove рассеиватели licence plate illumination.
- Turn out two nuts and remove the external handle.
- Turn out a nut and wring out a screw-driver an external overlay of a door of a back from clamps.
- Remove the handle for door lifting.
- Give fixture of loops to a door and remove a door.
- At installation of the door especially new, it is necessary to adjust its position.
- For door adjustment in directions to the left/to the right and upwards/downwards give bolts of fastening of loops to a door, expose a door in demanded position and tighten bolts with effort of 8 Nanometers.
- For door adjustment in directions upwards/downwards and inside/outside give bolts of fastening of loops to a body, expose a door in demanded position and tighten bolts with effort of 12 Nanometers. For a reversing of bolts at first:
- Remove a lens of the fixture of a luggage space;
- Turn out four bolts, separate a socket and remove the fixture;
- Wring out a screw-driver back section of furnish of a roof from clamps and remove it.
- If necessary adjust position of the drummer of the lock, moving it (tapping with a hammer) at the released fixture outside/inside and upwards/downwards. Preliminary remove the bottom panel of furnish of a doorway of a back. Upon termination of adjustment tighten bolts of fastening of the drummer with effort of 23 Nanometers and establish the panel.
- In summary adjust position of a lateral stopper.
- Installation is made upside-down. Tighten fixture with demanded efforts, use new clamps.
- In conclusion of installation adjust positions of the lever of a screen wiper (the Section condition Check, adjustment and replacement of brushes of screen wipers see).
|
- After installation check up, that the top point of hit of a stream of a washing liquid on glass was in the shaded area, and the bottom point – in a screen wiper scope.
|
|
|
|
|