LEXUS RX 300

1998-2003 of release

Removal, dismantling, assemblage and installation of forward seats

Components of assemblage of a forward seat


1 — the Headrest 2 — headrest Support 3 — the Armrest 4 — Electroconducting 5 — the Back 6 — a back Frame 7 — a back Cover 8 — the Heating element of a back 9 — Assemblage of a lumbar support 10 — the Cover 11 — a back Cover	12 — the Cutting washer 13 — a pillow Cover 14 — the Pillow 15 — the Heating element of a pillow 16 — a pillow Frame 17 — the belt Lock 18 — the Cover directing 19 — Internal covers of a pillow 20 — the pillow Panel 21 — a pillow Cover 22 — the Forward cover of a pillow 23 — Buttons of management of seat position

Components of an e/drive of a forward seat


1 — Assemblage of the mechanism of adjustment of an inclination 2 — Assemblage of vertical draught №2 3 — Switches of management of seat position 4 — the E/motor of a drive of the mechanism of adjustment of an inclination 5 — the E/motor of a drive of lifting of a forward part of a pillow 6 — Burn down electroconductings	7 — the Relay of management of seat position 8 — Assemblage of vertical draught 9 — Intensifying draught 10 — the E/motor of a drive of lifting of a back part of a pillow 11 — the Cover directing 12 — the E/motor of a drive of moving of a seat 13 — Assemblage of the mechanism of moving of a seat

PERFORMANCE ORDER

Remove covers directing by means of a screw-driver.
Turn out 4 bolts, separate sockets and remove a forward seat.
Remove headrests.
Remove buttons of management of seat position, turn out 4 screws and remove the panel of a pillow of a seat, having separated an electroconducting socket.
Turn out 3 screws and remove a cover of a pillow of a seat.
Turn out 2 screws and remove a forward cover of a pillow of a seat.
Remove from assemblage of a pillow electroconducting, turn out 4 bolts, and remove assemblage of a pillow of a seat.
Remove cutting washers, unhook hooks of a cover of a pillow and remove a cover together with a pillow.
Remove cutting washers and disconnect a cover from a seat pillow, if necessary remove a heating element of a pillow.

Do not pull electroconducting of a lateral pillow of safety.

Turn out 6 screws and remove internal covers of a pillow of a seat, having disconnected from them electroconducting.
Remove assemblage of a back of a seat.
Remove cutting washers, turn out 2 screws, unhook the holder and a hook of a cover of a back from a back frame.
Remove заглушки bolts, a washer, wavy washers and armrests.
Remove a back frame.
On a driver's seat turn out 2 bolts and remove assemblage of a lumbar support.
Remove cutting washers and disconnect a cover from a seat back, if necessary remove a heating element of a back.
Turn out a bolt and remove the seat belt lock.
Turn out 2 screws and remove switches of management of seat position.
Separate sockets and remove electroconducting.
On a driver's seat give 2 nuts and remove the relay of management of position of a seat and intensifying draught.
Remove covers directing, give 2 nuts and remove a seat belt arm.
Remove assemblage of the mechanism of adjustment of an inclination of a back together with assemblage of vertical draught №2 (only on a seat of the driver) and the e/motor of this mechanism.
On a driver's seat remove vertical draught, vertical draught №2 and e/motors of a drive of lifting of forward and back parts of a pillow.
Remove the e/motor of a drive of moving of a seat.
Assemblage and installation are made upside-down. Tighten fixture with demanded efforts.