LEXUS RX 300

1998-2003 of release

Repair and car operation



Лексус RX 300
+ Cars Lexus RX-300
+ Controls and operation receptions
+ Options and car routine maintenance
+ The engine
+ Systems of cooling of the engine, heating, ventilation and air conditioning
+ The power supply system and release of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Automatic transmission and interaxal differential
+ Трансмиссионная a line
+ Brake system
- Suspension bracket and steering
   The general information
   - Forward suspension bracket
      Removal, dismantling, assemblage and installation of a nave and rotary fist
      Removal, dismantling assemblage and installation of a rack of a suspension bracket
      Removal and installation of the bottom lever of a suspension bracket
      Check and replacement of a spherical support of a suspension bracket
      Removal, installation and check of the stabilizer of a suspension bracket
   + Back suspension bracket
   + Steering
   + Suspension bracket geometry
+ Body
+ Onboard electric equipment
+ Basic schemes of electric connections




Forward suspension bracket

Removal, dismantling, assemblage and installation of a nave and rotary fist

Removal and installation

Components of installation and assemblage of a nave and rotary fist

1 — the Rack of a forward suspension bracket
2 — the Tip of steering draught
3 — the Gauge of speed ABS
4 — Assemblage of a rotary fist and a wheel nave
5 — the Power shaft
6 — the Brake support
7 — the Brake disk
8 — Шплинт
9 — the Fixing cap

10 — Ступичный a bolt
11 — the Bottom lever of a suspension bracket
12 — Пыльник
13 — the Bearing
14 — the Lock ring
15 — the Rotary fist
16 — the Protective casing
17 — a wheel Nave


 PERFORMANCE ORDER

  1. Remove a forward wheel.
  2. Measure axial люфт the bearing of a nave of a forward wheel and axial palpation of a nave. For this purpose preliminary remove a brake support and a brake disk (the Brake system see the Head).

Reliably tie up a support so that it was not bent and the flexible brake hose was not loaded. Compare results of measurements to requirements of Specifications of the Head the Suspension bracket and a steering and if necessary replace the nave bearing. Establish to the place of a brake disk and a support.

  1. Take шплинт counternuts of a power shaft and, having squeezed out a brake pedal, turn out a counternut.
  2. Remove a brake support and a brake disk (the Brake system see the Head).

Reliably tie up a support so that it was not bent and the flexible brake hose was not loaded.

  1. Turn out fixture of the gauge of speed ABS and the holder of its electroconducting.
  2. Ослабьте, two nuts of fastening of a rack of a suspension bracket to a rotary fist.

Bolts yet do not take.


  1. Take шплинт nuts of a tip of steering draught, turn out a nut and by means of the special adaptation disconnect a tip of steering draught from a rotary fist.
  1. Turn out a bolt and two nuts and disconnect a spherical support from the bottom lever of a forward suspension bracket.
  2. Completely turn out two bolts of fastening of a rack of a suspension bracket to a rotary fist and remove assemblage of a rotary fist with a nave.

Do not damage a protective casing and a rotor of the gauge of speed ABS.

  1. Installation is made upside-down. After installation check up a signal from gauge ABS.

Dismantling and assemblage

 PERFORMANCE ORDER

  1. Take a screw-driver пыльник.
  1. Take шплинт nuts of fastening of a spherical support, turn out a nut and by means of the special adaptation remove a spherical support from a rotary fist.
  1. Remove a nave by means of the special adaptation.
  1. Выпрессуйте an internal holder (outside of) the nave bearing.
  2. Turn out 4 bolts and remove a protective casing of a rotary fist.
  3. Take a lock ring and выпрессуйте the bearing of a nave from a rotary fist.
  1. If necessary remove bolts of a nave by means of the special adaptation. Installation of bolts is made by a nut tightening.
  1. Assemblage is made upside-down. Tighten connections with demanded efforts. At installation пыльника level an aperture in it (for gauge ABS) with an aperture on a rotary fist. Use new ступичный the bearing and new шплинт nuts of fastening of a spherical support.