LEXUS RX 300

1998-2003 of release

Repair and car operation



Лексус RX 300
+ Cars Lexus RX-300
+ Controls and operation receptions
+ Options and car routine maintenance
+ The engine
+ Systems of cooling of the engine, heating, ventilation and air conditioning
+ The power supply system and release of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Automatic transmission and interaxal differential
+ Трансмиссионная a line
+ Brake system
- Suspension bracket and steering
   The general information
   + Forward suspension bracket
   - Back suspension bracket
      Removal, dismantling, assemblage and installation of a nave of a back wheel
      Removal, dismantling, assemblage and installation of a rack of a suspension bracket
      Removal and installation of the stabilizer of a suspension bracket
      Removal and installation of levers of a back suspension bracket
   + Steering
   + Suspension bracket geometry
+ Body
+ Onboard electric equipment
+ Basic schemes of electric connections




Removal, dismantling, assemblage and installation of a rack of a suspension bracket

Components of a rack of a back suspension bracket

1 — the Cover of a dome of a support of a rack
2 — the Plug
3 — the Cap
4 — the Emphasis of a rack of a suspension bracket
5 — Демпфер
6 — the Screw spring

7 — the Bottom saddle of a spring
8 — Assemblage of a rack of a back suspension bracket
9 — the Rack of the stabilizer of a suspension bracket
10 — the Flexible hose
11 — the Shock-absorber
12 — Draught of the gauge of adjustment of an inclination of headlights
13 — Electroconducting of the gauge of speed ABS

Removal and dismantling

 PERFORMANCE ORDER

  1. Remove a cover of a dome of a support of a suspension bracket and a corresponding wheel.
  2. At a corresponding complete set turn out a nut and disconnect draught of the gauge of adjustment of an inclination of headlights for the cross-section lever №2 back suspension brackets.
  3. Turn out a bolt and remove from a rack the holder of electroconducting of the gauge of speed ABS.
  4. Turn out a bolt and remove with скобы racks the holder of a flexible brake hose.
  5. Turn out a nut and disconnect from the shock-absorber a stabilizer rack.

If the hinge is turned together with a nut, keep it шестигранным a key on 5 mm.

  1. Ослабьте, two nuts of fastening of a rack of a suspension bracket to ступичной to assemblage.

Bolts yet do not take.

  1. Prop up ступичную assemblage by a jack and remove a cap from an emphasis of a rack of a suspension bracket.
  2. In need of rack dismantling ослабьте, but do not give completely the top (central) nut of fastening of a spring.
  3. Turn out three top nuts of fastening of a rack.
  4. Lower ступичную assemblage and remove two bottom bolts of fastening of a rack.
  5. Remove assemblage of a rack of a back suspension bracket.
  6. Establish two bolts with nuts in the bottom arm of fastening of a rack and clamp it in a vice.
  7. By means of the special adaptation compress a spring and, completely turn out a nut of fastening of a spring
  8. Remove the plug, the rack emphasis, the compressed spring, демпфер and the bottom saddle of a spring.
  9. Pressing and extending a shock-absorber rod make sure of smoothness of its course and absence of unusual sounds. At unsatisfactory results of check replace the shock-absorber.

Assemblage and installation

 PERFORMANCE ORDER

  1. Establish the bottom saddle of a spring and демпфер.
  2. By means of the special adaptation compress a screw spring and establish it on the shock-absorber.

The bottom coil of a spring should rest against a groove of the bottom saddle.

  1. Level an emphasis of a rack with bottom скобой the shock-absorber.

Installation of an emphasis of a rack

1 — Bottom скоба
2 — a rack Emphasis
  1. Establish the plug and temporarily tighten a nut of fastening of a spring.
  2. Remove from a spring pulling together adaptation and check up orientation of an emphasis of a rack.
  3. Installation is made upside-down.